Download Article

Download Article

Soft-shut toilet seats work because they have a special type of hinges that make the toilet seat close on its own very slowly and quietly. Some soft-close toilet seat hinges can exist adjusted to make the seat shut more slowly. Yet, non all soft-close toilet seats have adjustable hinges, but you'll take to remove the seat and inspect the hinges to observe out if yours are adjustable. If your soft-close seat isn't working like it used to and yous tin can't arrange the hinges, you might take to fix it by replacing the swivel dampers with a new set.

  1. 1

    Open upwardly your toilet seat and look for metal hinges that sit on vertical pegs. Metal peg-fashion hinges are one of the 2 main types of hinge assemblies that soft-shut toilet seats may use. Look for metal pegs coming up from round plates fastened to the back of the toilet bowl, which the hinges on the toilet seat slide onto.[1]

    • If you don't run into this type of hinge assembly, your soft-shut seat probably has a plastic clip-on type of hinge assembly.

    Tip: If your toilet seat is loose, this doesn't have to practice specifically with the soft-close hinges. You can make adjustments to the bolts that agree the seat in place to prepare a loose toilet seat. The merely reason yous would need to adjust soft-close hinges is if your soft-close seat is not closing at the right speed.

  2. 2

    Lift the toilet seat directly up off the hinges from the upright position. Get out the soft-close seat in the fully open position. Hold the seat at the top and bottom or at both sides and carefully pull it direct up off the metal pegs.[2]

    • If your toilet seat doesn't lift straight off, effort tilting information technology forward just a few degrees and see if you can lift it off from that position.
    • If yous can't slide the seat off the pegs, try pressing in the hinges with your thumbs and lifting it off. Different soft-close seats with peg-way hinge assemblies may accept dissimilar locking mechanisms.

    Advertisement

  3. 3

    Prepare the toilet seat upside-downwardly on a flat work surface. Flip your seat over and so that the metallic hinges are exposed. Lay the seat flat on a table or another flat surface.[3]

  4. 4

    Pull out the cylindrical dampers on both sides of the back of the seat. Catch the dampers between your fingers. Pull the cylinders all the way out of the holes they sit in.[4]

    • These dampers are what actually control the speed at which the seat closes.

  5. 5

    Rotate the dampers towards the back of the seat to make it close more slowly. Spin each hinge damper towards the back of the seat, ensuring that yous align the shape of the dampers with the shape of the holes that they slide into. This will slow down the seat's hinges so they close it more than softly and quietly. [5]

    • Not all soft-close toilet seat hinges are adjustable. If at that place are notches on the dampers that make it so you tin can just take them in and out in ane position, they are not adjustable.
    • If your hinges are adaptable, they may exist hexagonal or accept multiple notches that allow you to put them in at different positions. They might also exist labeled with "slow/fast" and directional arrows.
    • Depending on the specific soft-close toilet seat you lot have, there might be 2-3 different positions you can prepare the dampers in to control the speed of the seat.

  6. 6

    Slide the hinge dampers dorsum into the hinge assembly. Push the cylindrical damper back into the hole in the hinge assembly on 1 side. Repeat this for the damper on the other side.[6]

    • If the soft-close dampers take multiple positions y'all can ready them to for different speeds, double-check that you are putting them in at the same position on both sides of the seat. Otherwise, the seat and lid might shut at different speeds.

  7. 7

    Put the toilet seat dorsum on the toilet bowl. Align the holes in the seat's hinges with the begs on the toilet bowl. Set the seat back on the hinge pegs in the upright position.[7]

    • If the hinges accept a locking machinery, make sure you push the seat all the manner onto the pegs until the hinges snap into place.

    Advertisement

  1. 1

    Shut the toilet seat and look for rectangular plastic covers at the back. Plastic clip-on swivel assemblies are the second main type of swivel assemblies that soft-close toilet seats can have. Look for rectangular plastic pieces that come up off the dorsum of the toilet seat, which cover the bolts in the toilet bowl that the seat's hinges clip onto.[eight]

    • If you don't see a plastic hinge assembly, your soft-close seat probably has metal peg-style hinges.

  2. 2

    Slide the seat forward from the downward position to remove information technology. Go out the seat all the way down then that it is resting in the airtight position on the toilet bowl. Flip upwards the plastic swivel covers at the back of the seat, then grasp the seat from the back and pull it straight forward off the toilet.[nine]

    • If you are unable to slide off the toilet seat, yous might have to unscrew the bolts from underneath on the back side of the toilet bowl to remove it. Soft-shut toilet seats with prune-on swivel assemblies tin can have slightly unlike attachment methods, depending on the specific make and model.

  3. 3

    Identify the soft-close seat upside-down on a apartment surface. Flip the seat over so that the hinge assembly is exposed. Lay it downwardly on a apartment surface with the hinges facing you.[10]

  4. 4

    Use needle-nose pliers to pull the cylindrical dampers out of the hinge assembly. Grasp the edge of ane of the dampers between the pliers and pull to slide it out of the hole it sits in. Repeat this for the damper on the other side.[xi]

    • There might exist a plastic cover on the underside of the hinge associates that you have to pop off to run across the cylindrical hinge dampers. If then, just pry information technology off with your fingers and set information technology bated. Yous might also be able to lift the whole swivel associates out of the toilet seat to work on information technology more easily.

  5. 5

    Plough the hinge dampers towards the dorsum of the toilet seat to slow it down. Rotate each swivel damper towards the back of the seat to make it close more slowly and quietly. Look at any notches or markings on the dampers and look at the shape of the holes in the swivel assembly to determine how far to plow the hinges to reinsert them at a new position.[12]

    • If there are only ane gear up of notches on the dampers or their shape makes information technology so that they tin can merely be inserted into the hinge assembly in 1 position, they are not adaptable.
    • Adjustable hinges are sometimes hexagonal or accept different notches so yous tin can insert them at unlike positions. They could likewise take directional arrows and be labeled with "slow/fast."
    • At that place might be 2-3 dissimilar positions you lot tin can set the dampers in to fix the soft-close seat to different speeds, depending on the make and model of the seat.

    Tip: If your soft-close toilet seat'south hinges are not adaptable, you can replace them with a new set, which costs less than $15 USD, to make your seat work like new again. You lot could too supersede the entire seat for around $fifty USD or less.

  6. 6

    Utilize your fingers to push button the hinge dampers back into the hinge assembly. Insert the cylindrical damper dorsum into the hole in the hinge assembly on one side in its new position. Do the same with the damper on the other side of the seat.[13]

    • Make sure yous're putting both the dampers in the same position on their corresponding sides of the swivel associates, or the seat and lid could shut at different speeds.
    • If you lot removed the hinge assembly from the seat or popped a cover off the hinge assembly, supplant these at this fourth dimension as well.

  7. vii

    Slide the toilet seat dorsum onto the bolts at the back of the toilet basin. Flip the toilet seat back over and ready it flat on the toilet bowl. Align the clips at the back of the hinge assembly with the bolts on the toilet bowl, and then push the seat until it clips all the way back on. Press the plastic covers back on top of the bolts.[fourteen]

    Advertisement

Inquire a Question

200 characters left

Include your email accost to go a message when this question is answered.

Submit

Ad

  • If you can't arrange the hinges on your soft-close toilet seat to make it close slowly and quietly over again, you tin can replace the swivel dampers or the whole seat at a low cost.

  • If the speed of your toilet seat is fine, but y'all desire to tighten the seat to terminate it wobbling around, you don't need to accommodate the hinges. You lot can try tightening the bolts on the underside of the toilet bowl to fix a loose seat.

Thanks for submitting a tip for review!

Ad

Things You lot'll Need

  • Needle-olfactory organ pliers

References

Nearly This Article

Thanks to all authors for creating a folio that has been read 199,362 times.

Did this article help you?